Skip to main content

Belgian Tripel Brew Day

08-08-01Yesterday I finally got to brew my Belgian Triple. I still need to think of a good name for it and I am taking suggestions. I recieved all of my ingredients from Austin Homebrew on Wednesday and quickly discovered that I had a few problems. The first was that the Wyeast 1214 Belgian Ale yeast was warm to hot. The summers here in Texas get scorching and the trip from Austin to Lubbock is a long hot one. I did order an ice pack, but that too was warm by the time it got here. The second was that Tettnanger and Saaz came in 2-3% less than what I was anticipating. I modified the recipe a bit to get similar IBUs out of the brew. I also change a few of the times in the mash and hopping schedule.

08-08-02Friday morning, around 9:30 or so, I smacked the pack to get the yeast woken up. I didn’t plan on actually starting the brew till 4:00 in the afternoon so that gave it plenty of time to puff up. The smack pack never really puffed up much past the first 2 hours. You can see in the picture to the left that it didn’t to much. I was a bit concerned but decided that it was too late to change anything.

I mashed my grains (12 lbs Belgian Pils, .5 lbs Belgian Pale, and .5 lbs unmalted wheat) for 90 minutes at 152ºF. The strike water temperature came in at 165ºF. After the 90 minutes I took the temperature again just to see how good my new mashtun held temps. The theomerter read 150ºF! I was pretty pleased what that result. I was acutally expecting it to drop much more than that.

I collected about 2.5 gallons of water from my orginal 4 gallons. I added another 3 gallons of water that came in at 170ºF. I collected my second runnings in the main boil pot and about a gallon of third runnings in a secondary pot. The point of this is to add it to the main pot once some of it boils away. I only have a 5 gallon pot, so trying to get the most out of it is tough. This is the method I have been using and it has worked. It also allows me to get the most out of the grains that I can.

08-08-07

08-08-06I boiled each pot for 30 minutes and then combined them. I also added 1 oz. of the Tettnanger at this time. I continued the boil for another 30 minutes and added .5 oz of Saaz hops. 15 minutes later I added another .5 oz of Saaz and 5 minutes after that I added a BrewVint Yeast Fuel. Finished out the boil for another 10 minutes and started the cooling process. 90 minute total boil. When all was said and done I had collected just under 4 gallons of wort, I was shooting for 3.5 gallons, and had a gravity of 1.074.

I was pretty happy with that, but it fell short of the gravity I wanted. Part of that was due to the increased wort volume and I think Beer Tools Pro overestimated the amount of sugar I would be able to get. I didn’t add anything to bring the gravity up to where I wanted it becasue I wasn’t sure about the health of the yeast. I pitched the yeast closed it all up and went over to a friends. I came back 4 hours later and the airlock was 08-08-04bubbling away. Success! The beer isn’t going to be as strong as I had intended but that’s ok. This is my first ever big beer and I am happy with the results thus far. If I would of done some more thinking and planning I would of tried to make a session beer with whatever sugars were left in the grain bed. Something to consider next time.

The Tripel should be in the primary for a week and the secondary for another week. Then it is bottling time. My apartment stays at a pretty consitent 75ºF so it should be just fine. And finally my new brewing partner enjoying all of the new smells. If you click the read more link after this you can see some more pictures from the brew day. (more…)

07-31-01

Belgian Tripel Recipe

07-31-01Now that I am finally established in Texas I can get back to homebrewing again. It has been a long time since I brewed the SB Birthday Beer. Does the date of that post really go all the way back to Feburary. That sucks. I’ve been really digging Belgian beers for the past few months and have been coming up with ideas in my head about what all I need to do to make it as good as it can be. So I came up with the following recipe:

  • 12 lbs Belgian Pils
  • .5 lbs Belgian Pale
  • .5 lbs Wheat malt
  • .25 0z Tettnanger (4.5% at 120 mins)
  • .25 0z Tettnanger (4.5% at 90 mins)
  • .25 0z Tettnanger (4.5% at 60 mins)
  • .25 0z Tettnanger (4.5% at 30 mins)
  • .5 oz Saaz (5.0% at 10 mins)
  • Yeast: WLP530 (Abbey Ale) or another Belgian Strong if unavialable

I plan on mashing the grains at 152 degrees for 90 minutes to try and get as much sugar out of them as I can. I hope to collect a total of 5 gallons of wort for boil when all is said and done. I then want to boil for two hours and bring down the level of wort to around 3.5 gallons. I haven’t brewed here before and I am almost 3,000 ft. higher in elevation so I don’t know if the boil time will need adjusting.

I will ferment in the primary for a week, switch to a secondary for another week, and then bottle and contition for 2-3 weeks. I hope to have a nice estery beer that comes in between 9.5-9.7% abv. My SG goal is going to be 1.090, maybe a bit higher or lower depending on my effiency.

My hop choices came down to English (Fuggles and Goldings) or the German hops I picked. Saaz hops has a history of being a bit more fruity and I want those esters to shine. With such a long boil I wanted to strech out the primary hops and split them up into four small additions. It might add a bit of complexity but will make it not overpowering. I am still considering just a single addition at the hour mark, but I still can’t make up my mind. The final IBUs should come in at about 28 IBUs. I’m going to ferment on the upper edge of the recommended temperature at 75 degrees or so.

Is there anything I missed or any other considerations I should look at before brewing this bad boy up. I’m hoping to make a go at it this weekend or next depending on how fast the ingredients ship and how fast I can build my mash tun.

SB Birthday Beer

09-02-16-01One of my dear friends is turning 21 soon and she asked if I could make a homemade beer for her. Naturally I was thrilled that someone other than my roommate and I wanted to drink my beer, so I accepted the challenge. She is a big tea freak and wanted some tea flavor in the beer. I decided that a wheat beer would be ideal for a tea flavored beer. Wheat beers carry a lot of complex flavors that I thought would compliment the beer nicely.

I made a trip out to my homebrew store last week and got all of the necessary supplies. Below is a list of everything I picked up:

  • 3 pounds American 2-Row Pale malt
  • 3 pounds Wheat malt
  • 1 pound 60 Crystal malt
  • 1 oz Saaz hops (3.6%)
  • 1 tube liquid American Hefeweizen Ale yeast

I know that most wheat beers generally have a 50% wheat grain bill, but I wanted to make this an amber colored wheat beer and the homebrew store was running a bit low on wheat malt. This is supposed to make about 4 gallons worth of beer. I started my mash trying to get the grains to 110 degrees for 15 minutes, then 125 degrees for 15 minutes, and then finally 153 degrees for 45 minutes. All of these different temperatures are an attempt to release different characteristics from the wheat.

I boiled for the normal 60 with a half ounce of the Saaz going for the full boil and the other half ounce going for the last 15. I took the beer off the burner and put two teabags into wort leaving them there for only a minute or so. the  Everything went well and I cooled down the wort and pitched the yeast. The next day I took a look at my airlock and bubbles were firing away.

09-02-17-02I was unsure of the tea she wanted to use when I got my supplies. The day before brew day she gave me Chi Tea. I’m not a big tea guy so I made up a cup and found it to be very gingery. Not something I would put with a wheat beer with hefeweizen yeast. That’s the reason for such a short time in wort. I think the Chi would of gone great with a winter warmer type beer as the flavors are those I typically taste in a winter beer. At first glance I achieved an effieceny of 75% from my batch sparge and we are looking at an ABV of 4.3%. I’m pretty happy with that and I’m looking forward to trying this beer as it ages through and finally is ready to drink out of a bottle on her birthday in March.